To see all of the Ducati models we offer click (OR SEE BELOW) ECUnleashed Tuning Technology is now offering our ECU reprogramming service for Ducati Motorcycles. Choose from an extensive list of performance Tune Files or have us develop a completely custom tune for your Ducati. ![]() Ducati ECUs typically feature a “closed loop” system whereby conventional tuning cannot modify the low RPM range, often requiring custom programming (“re-mapping” of the ECU) and time on a dynamometer (or “dyno”) to tune across the full range. Ducati models with the Marelli 59F, 59M and 5AM ECU. Remove body panels uppers and lowers A B C SP electronics ( CGS2 kit installation procedure on Ducati motorbikes models 748 – 749 – 999 – 1098 – 848 – 1198 Streetfighter ) 2) Place the CGS2 eBox near Dashboard. We recommend to arrange all wiring on the right side (Gear indicator display is optional) – Gear indicator display – CGS2 eBox – CGS2 main wiring – CGS2 accessory wiring (*) *NOTE: keep this wiring away from dashboard’s connector! ECU can be connected to AIM loggers in two different ways: directly, or using the connector placed on the dashboard. – Direct connection between AIM loggers and Marelli IAW 5AM2 ECU IAW 5AM2 is equipped with two 38 pins connectors, named “Body ” and “Engine” – see below: “engine” is black (on the left). “Body” connector is grey (on the right). To connect AIM loggers to Ducati ECU: • connect AIM cable labelled CAN+ to pin 20 of “Body” connector. • connect AIM cable labelled CAN- to pin 29 of “Body” connector. • Vbatt is on pin 17 (vehicle master switch). 2.2 – Dashboard connector Connector is equipped with 26 pins and it is placed on the back of the dashboard. To connect AIM loggers to ECU using the dashboard connector: • connect AIM cable labelled CAN+ to pin 19 (green/black twisted cable) connector. • connect AIM cable labelled CAN – to pin 26 (grey/green twisted cable) connector. • Vbatt is on pin 23 – red /black cable – vehicle master switch. Warning: to use Marelli dashboard, please remove 120 OHM resistance placed between CAN+ and CAN-; otherwise Marelli dash does not work. Ducati direct lever sensor installation: 1) Remove original lever assembly 2) Fit the new lever and tight nut. 3) Set toe peg in correct position 4) Connect the sensor with CGS2 and try it: when sensor is pressed a dashes appears on CGS2 SP electronics DUCATI DIRECT LEVER SENSOR INSTALLATION NOTE – The sensor was designed to offer you the best performance and don’t need mechanical maintenance: you mustn’t disassemble or try to repair the lever (See warranty details on our website www.spelectronics.it). – If you intend use our lever sensor with your preferred quick shifter electronic system (Power Commander, Rapid Byke, ecc.) we recommend you to use specific wiring interface (see photo below). Alls connector manipulations on sensor invalidate warranty. SP electronics DUCATI DIRECT LEVER SENSOR INSTALLATION SP electronics is working everyday to improve quality on our products. Unfortunately, perhaps some sensor doesn’t work after some time. Remember that SP electronics will apply warranty substitutions or repairs when products satisfies original complying. When replacing the ECM (SAE term: PCM) or the Transponder ECU a “handshake” procedure must be performed. This ECU ID communication is necessary to enable the Transponder ECU and the ECM to recognize each other before the vehicle will start. Complete ECU communication using the following steps: 1. Insert a Master key into the ignition cylinder. Ninja storm 3 all characters crack only. Turn the ignition ON (engine OFF). Short Tc and CG terminals of DLC3 using the Diagnostic Check Wire (SST 0 or equivalent) and leave for 30 minutes. After 30 minutes, turn the ignition OFF and remove check wire from DLC3. Register any additional keys as necessary. Start the vehicle to confirm successful ECU communication. Key Programming: To program or delete a key, a registered Master key is necessary unless the Transponder ECU has been reset or replaced. The Transponder ECU system incorporates a black “Master” key and a gray “Sub” key. The process during registration of these two keys is identical. The key itself now determines if it functions as Master or Sub, not the registration procedure. The maximum number of allowable Master and Sub keys vary by model. Refer to the chart below. Incoming search terms: •. The PE-ECU-1 can be installed on virtually any 1,2,4,6 or 8 cylinder even-firing engine that requires fuel injection and/or ignition control. All of the functions of the ECU can be adjusted by using a laptop or PC running Windows.
0 Comments
Leave a Reply. |